How to Replace the Replacement Key Battery For the Saab 9-3
Saab owners must follow a set of special steps to install an additional ignition key. It requires dealer service using a handheld computer called Tech-2. Then a new key and transponder need to be bought and programmed to the car.
It is recommended to rotate your keys so that one does not wear out faster than the other. This will also ensure that your keys remain in pristine condition.
Replacement Case
The new key fobs for keys are not like the older Saab keys. They're equipped with electronic devices which make it hard to copy. That has made car theft much more complicated than it was 20 years ago. It also makes it more expensive to replace keys lost.
Saab 9-3 owners must have two working keys. It's expensive to replace a lost or damaged key since it requires replacing the CIM module, and changing the locking cylinders. Dealers will typically charge $100-$200 to do this.
There are a few ways to avoid these costly. Certain parts suppliers will utilize the code of the spare key to cut a brand new metal blade for less than that of a dealer. The key, however, must be identical to the original to work correctly within your car.
Follow these steps to replace the case. You'll need a flathead screwdriver along with some patience. With the screwdriver, break away the plastic and take out the emergency key. Once the case is open, remove the electronic components and place them into your new case. Place saab key replacement near me with the correct badge inside the case.
Replacement Battery
The Saab 9-3 replacement battery is a low-cost part that can be quickly and easily replaced. The YouTube video of Cyclone Cyd shows how to replace the battery for the remote fob in only four steps. This tutorial should work with any modern Saab key fob. However, the procedure could differ slightly.
The first step is to locate the button that will release the backup key within the fob. This is usually located just below the Saab logo on the back of the fob. Next you will need an screwdriver with a flat head to insert into the tiny hole in this button. This should be enough to unlock the case of the fob so that you can replace the battery.
After you have installed the new CR1632 batteries, you can put back together your remote key fob. Then, you can program it into your car. The entire process shouldn't exceed an hour. It's a simple procedure that doesn't require special tools.
The process is a bit more complicated if you lose your key, but it's possible. The dealer will first need to read the VIN of the vehicle and order the replacement TWICE module as well as key blade with the proper unique code. The dealer will then need to program the key using MDI, a brand new software tool.
Replacement Key Fob
The key fob is a device that locks and unlocks your car, it has a battery inside. The batteries are able to last for and will eventually fail. This is a problem that happens with all cars, and the good news is that you can change the batteries on most key fobs without replacing the entire case. You can buy replacement fobs on Amazon that come with all the electronic components already installed, so you'll be able to simply open the case and replace the batteries that were in the case. It is important to note that you'll need to take out the emergency key first, and you can do this by inserting the small screwdriver flathead into the slot found in the middle of the case. The case will split when you work the screwdriver all around it.
When you're ready to replace the keys ensure that you have spare keys, because this can cut down the total cost by a substantial amount. If you have an extra key, you can ask the dealer to cut it and program it to your vehicle. This is a lot less expensive than buying a new key fob.
It is possible to add a second key to your car in the event that you don't have one, but it requires an extensive amount of research and work. A second key can cost around a hundred dollars and it also requires the programming of the car's computer. This can be accomplished by a professional, however it's a costly option for the majority of owners.
Replacement Ignition
The modern SAAB 9-3 features a more sophisticated alarm system built around a key code. If you lose your only key, it may be costly to purchase a new one since the car needs to have a specific computer installed and also be programmed to accept a brand new key. Even dealers can charge hundreds of dollars to program an entirely new key, in the event that they are unable to do it.
Dealers will charge you a premium to replace your car's computer (also known as the CIM or SAAB twice) when you lose the only working key. Instead we can reprogramme the EEPROM of your current car computer to allow it to be programmed to accept a second key, which will save you more than 50% of the amount you spend at a dealer.
If you've been an owner of a 03-11 SAAB 9-3, you likely are aware that the ignition key isn't really all that robust. They can become incredibly sticky, and the buttons are known to fall off of them at times It is recommended that you consider replacing your ignition key if it isn't performing as it should. It's good to know that replacing the ignition key isn't as complicated as it seems and can be done quickly using the appropriate tools.